Skip to content

The ROCKWOOL Guide: Reading a stone wool batt label

Volcanic rock, melted and spun to wool in a Danish gravel pit — insulation against heat, fire, and noise since 1937.

By The Super Arbor Desk

ROCKWOOL — from the Super Arbor brand hall series
In this article
  1. The record: ROCKWOOL, year by year
  2. Reading a stone wool batt label
  3. Three products. One stone.
  4. The desk’s read
  5. Questions, answered plainly
  6. Where to buy

Volcanic rock, melted and spun to wool in a Danish gravel pit — insulation against heat, fire, and noise since 1937.

ROCKWOOL began in 1909 as Korsør Stenforretning, a Danish gravel business, and has spun stone wool since 1937, when the first wool left a factory built in a Hedehusene gravel pit. This hall holds that record — the New Jersey license bought for 5,000 dollars, the binder that made the wool water-repellent, the Ontario plant that carried it across the Atlantic — alongside the working exhibits: a wall opened layer by layer, a batt label decoded, and the three stocked lines set side by side.

Shop all ROCKWOOL at Super Arbor →

The record: ROCKWOOL, year by year

1909 — A gravel pit on Omø

H.J. Henriksen and Valdemar Kähler start Korsør Stenforretning, a stone and gravel business, with a pit on the small Danish island of Omø in the Great Belt. For its first three decades the firm deals in aggregate, not insulation.

1937 — First stone wool at Hedehusene

After Finn Henriksen's 1935 US study tour, the firm buys rights to Baldwin-Hill's stone wool technology for Scandinavia and Germany at USD 5,000. Production starts in 1937 at a factory in the Hedehusene gravel pit and at Skövde, Sweden — first-year net sales, DKK 150,000, with around 20 employees.

1954 — Binder, water repellency, dimensional stability

A second Baldwin-Hill licence, taken in the early 1950s, covers impregnation — adding binder that makes the wool water-repellent and dimensionally stable. Batts gradually become the main product, per the company history. In 1954, Gladbeck in Germany's Ruhr becomes the first production outside Scandinavia.

1976 — Rockwool International A/S

The Danish parent A/S Rockwool is split into Rockwool International A/S as parent company, holding the group's research and development department. By the decade's end the group runs ten factories across Denmark, Norway, Germany, the Netherlands, and Wales, with 3,999 employees.

1988 — First factory outside Europe

The group acquires a plant in Milton, near Toronto, from the Lafarge Group and names the Canadian company Roxul Inc. A second Canadian factory is acquired at Grand Forks in 1999. Milton remains the North American address printed on ROCKWOOL data sheets today.

1996 — Nasdaq Copenhagen listing

ROCKWOOL A/S is introduced to the Nasdaq Copenhagen stock exchange, per the Group's investor pages, trading in two share classes — ROCK A and ROCK B. The registered office remains at Hedehusene, where headquarters moved from Korsør in 1958.

2018 — Roxul becomes ROCKWOOL

On 1 January 2018, Roxul Inc. adopts the parent name across North America under a logo whose volcano marks the material's source in volcanic rock. Per the announcement, the rebrand covers the residential, commercial, roofing, OEM, and technical insulation lines.

2025 — The group today

Per its 2025 annual report, the ROCKWOOL Group closes the year with net sales of EUR 3,877 million, more than 13,000 colleagues in around 40 countries, and sales in more than 120. It describes itself as the world leader in stone wool products.

Reading a stone wool batt label

The specimen: one line from the Comfortbatt® wood-stud table. Three marks tell you exactly which wall the batt was made for.

The specimen: COMFORTBATT® R-23 · 5.5" x 15.25" x 47"

R-23 — Thermal resistance

R-value is resistance to heat flow, tested to ASTM C518 — higher is slower. On ROCKWOOL's wood-stud table, R-23 is the 2x6-wall entry. The full ladder runs R13 and R15 for 2x4 walls, R21 through R23 for 2x6, then R30 at 7.25 inches and R38 at 9.5 for joist and attic work. The steel-stud table is separate: R15, R24, R30, R32.

5.5" — Thickness = stud depth

Stone wool buys its R-value by the inch, so thickness is tied to the framing it fills: 3.5 inches matches a 2x4 bay, 5.5 inches a 2x6, 7.25 a 2x8. ROCKWOOL produces the batt at a slight over-thickness for a friction fit, and the flexible edge compresses on entry and springs back against the studs — the design the company says maintains the labeled R.

15.25" x 47" — Width names the framing

The width is the tell. 15.25 inches fits wood studs on 16-inch centers; 23 inches fits 24-inch centers. Steel-stud batts run 16.25 and 24.25 inches wide by 48 long, on their own table of the same data sheet. Read the width before the R — the right R-value cut for the wrong bay leaves the gaps that undo it.

Dimensions, R-values, and test standards per the ROCKWOOL Comfortbatt® technical data sheet, issued 05-2025.

Three products. One stone.

Batts for heat, batts for noise, boards for the envelope. Super Arbor stocks the batts deep and the boards beside them; the desk quotes the rest.

R13–R38 · Comfortbatt®

The thermal line: semi-rigid stone wool batts for exterior wood- and steel-stud walls, attics, basements, and exposed floors. The wood-stud table runs R13 and R15 at 3.5 inches through R38 at 9.5, with the flexible edge supplying the friction fit. Noncombustible per ASTM E136, flame spread and smoke indices of 0 per ASTM E84, GREENGUARD Gold certified.

Where it fits: Exterior walls, attics, and basements — anywhere the assembly needs cavity R-value.

3–6 in · Safe'n'Sound®

The interior line: a stone wool batt ROCKWOOL designs for superior fire resistance and acoustic performance in interior wall cavities, floors, and ceilings, in wood and steel framing. It comes in 3- and 6-inch thicknesses sized for 16-, 19.2-, and 24-inch framing, and the company positions it on fire and sound performance rather than a thermal R-value.

Where it fits: Interior partitions bought for quiet — bedrooms, baths, media rooms — plus noncombustible fire performance.

R4.2/in · Comfortboard® 80

The continuous-insulation line: a rigid stone wool board installed outside the studs as non-structural exterior sheathing, covering the framing the cavity batt cannot reach. ROCKWOOL rates it at R-4.2 per inch at 75 °F and 8 lb/ft³ density — noncombustible, melting point approximately 2,150 °F (1,177 °C), and vapor-permeable for what the company calls fast outward drying.

Where it fits: Exterior continuous insulation over sheathing, above and below grade.

⚠ Worth reading twice: Fire and sound numbers belong to tested assemblies, not to a batt alone. ROCKWOOL states its stone wool is noncombustible (ASTM E136) with a melting point of approximately 2,150 °F (1,177 °C), and that Comfortbatt can add up to 15 minutes of fire protection to a wall assembly — but a wall's fire rating and its acoustic performance come from the full listed design. Follow the listed assembly and local code.

The desk’s read

The order logic nobody writes down — voiced as Super Arbor’s desk, not the brand’s claim.

Pick by wall, not by aisle

The desk's read: the three lines split cleanly. The exterior envelope and anything with a code R-target gets Comfortbatt; interior partitions bought for quiet get Safe'n'Sound; thermal bridging outside the sheathing is Comfortboard's job. Crossing them wastes money in one direction and misses the point in the other — decide which wall you are standing at first.

The width mistake

The desk's read: measure stud spacing center-to-center before ordering, because batt width is framing-specific — 16-inch centers take the 15.25-inch batt, 24-inch centers take the 23. Steel framing takes its own widths, 16.25 and 24.25. An R-value cannot rescue a batt cut for the wrong bay; a tape measure can, in under a minute.

Money math by the inch

The desk's read: R rides on thickness, so buy the R the cavity can actually hold — 3.5 inches of depth is an R15 wall, not an R23 one. ROCKWOOL's own literature ties the labeled R to a gap-free, void-free fit and builds the flexible edge to spring the batt tight against the framing. Match batt depth to stud depth, then stop spending.

The first buy

The desk's read: start with one bag of Comfortbatt for the target wall, a serrated blade — ROCKWOOL suggests a bread knife — gloves, and long sleeves per the manufacturer's safe-use sheet. Cut and fit one bay, check the friction hold, then commit to the rest. Vapor retarder questions go to local code, not to the aisle.

Questions, answered plainly

What is ROCKWOOL insulation made of?

ROCKWOOL stone wool is made from basalt — a volcanic rock — and recycled slag, a by-product of the steel industry, melted and spun into fine fibers. The company's volcano logo, adopted with the 2018 North American rebrand, refers to volcanic rock as the source material of all its products.

Does ROCKWOOL insulation burn?

ROCKWOOL stone wool is noncombustible as determined by ASTM E136, with flame spread and smoke developed indices of 0 under ASTM E84. The company states its products have a melting point of approximately 2,150 °F (1,177 °C) and will not develop smoke or promote flame spread when directly exposed to fire.

What is the difference between Comfortbatt and Safe'n'Sound?

Comfortbatt is ROCKWOOL's thermal batt for exterior wood- and steel-stud walls, attics, basements, and exposed floors, sold in R13 through R38. Safe'n'Sound is the interior batt, designed per ROCKWOOL for superior fire resistance and acoustic performance in partition walls, floors, and ceilings — positioned on sound and fire rather than an R-value.

Does ROCKWOOL insulation absorb water or grow mold?

Per ROCKWOOL, stone wool does not wick water — bulk water drains from the surface rather than soaking into the batt — and the material is vapor-permeable, so incidental moisture dries out. Comfortbatt passed ASTM C1338 for fungi resistance, and the company states its inorganic stone wool does not support mold or fungus growth.

What do the sizes on a Comfortbatt bag mean?

Width encodes framing: 15.25 x 47 inches fits wood studs on 16-inch centers, 23 x 47 fits 24-inch centers, and steel-stud batts measure 16.25 or 24.25 by 48 inches. Thickness carries the R-value — 3.5 inches for R13 and R15, 5.5 for R21 and R23, 7.25 for R30, 9.5 for R38 — per the 05-2025 technical data sheet.

Is ROCKWOOL the same company as Roxul?

Yes. Roxul Inc., the group's North American company since a 1988 plant acquisition in Milton, Ontario, adopted the parent name on 1 January 2018, and its product lines now carry ROCKWOOL branding. The Danish parent — founded 1909, producing stone wool since 1937 — is headquartered in Hedehusene and listed on Nasdaq Copenhagen.

Where to buy

The ROCKWOOL lines above are live catalog — priced in the open, the same number for everyone. Insulation is a coverage buy: send the list — however you have it — and a human specialist prices every line and checks the math.

Shop ROCKWOOL →  ·  Send your material list

Citations & marks

Sources: ROCKWOOL Group corporate history ("Short History of the Rockwool Group," 2003) and history pages · rockwool.com North America product pages and FAQ · Comfortbatt® technical data sheet (05-2025) and product brochure · Comfortboard® 80 and Safe'n'Sound® product pages · ROCKWOOL Group investor pages and 2025 annual report release · ROCKWOOL and PR Newswire rebrand announcements (2017–2018). Era and anatomy imagery: styled visualizations, not archival photographs or ROCKWOOL drawings.

Comfortbatt®, Comfortboard®, and ROXUL® are registered trademarks of the ROCKWOOL Group in USA and ROXUL Inc. in Canada; ROCKWOOL™ is a trademark of the ROCKWOOL Group; SAFE'n'SOUND® is a registered trademark used under license by Masonite Inc. Super Arbor is an independent retailer; brand marks remain the property of their respective owners.

From the Journal

Keep reading

All articles
  1. 8 min read

    The Owens Corning Guide: Reading a PINK batt label

    Spun glass since 1938; a registered color since 1987.

  2. 8 min read

    The Daltile Guide: Reading a tile spec sheet

    Begun in a Dallas Quonset hut in 1947 — porcelain, ceramic, and stone, under Mohawk Industries since 2002.

  3. 8 min read

    The Eaton Guide: Reading the breaker label

    Seven truck axles built by hand in 1911; a century later, the panel on the basement wall.

  4. 8 min read

    The Schlage Guide: Reading a Schlage listing

    The push-button lock of 1920, the cylindrical bore it required, and a century of graded hardware since.

  5. 8 min read

    The Legrand Guide: Reading a receptacle spec line

    From a Limoges porcelain workshop, 1865, to the wiring devices inside the wall — electrical since 1919.

  6. 8 min read

    The MAPEI Guide: Reading the mortar bag

    Adhesives, mortars and grouts from a company founded in 1937 on the outskirts of Milan — family-run for three generations.